Datasheet Texas Instruments OPA830IDBVT — Datenblatt

HerstellerTexas Instruments
SerieOPA830
ArtikelnummerOPA830IDBVT
Datasheet Texas Instruments OPA830IDBVT

Single-Supply-Operationsverstärker mit geringem Stromverbrauch 5-SOT-23 -40 bis 85

Datenblätter

Low-Power, Single-Supply, Wideband Operational Amplifier datasheet
PDF, 843 Kb, Revision: F, Datei veröffentlicht: Aug 28, 2008
Auszug aus dem Dokument

Preise

Status

Lifecycle StatusActive (Recommended for new designs)
Manufacture's Sample AvailabilityYes

Verpackung

Pin5
Package TypeDBV
Industry STD TermSOT-23
JEDEC CodeR-PDSO-G
Package QTY250
CarrierSMALL T&R
Device MarkingA72
Width (mm)1.6
Length (mm)2.9
Thickness (mm)1.2
Pitch (mm).95
Max Height (mm)1.45
Mechanical DataHerunterladen

Parameter

2nd Harmonic67 dBc
3rd Harmonic60 dBc
@ MHz5
Acl, min spec gain1 V/V
Additional FeaturesN/A
ArchitectureBipolar,Voltage FB
BW @ Acl310 MHz
CMRR(Min)76 dB
CMRR(Typ)80 dB
GBW(Typ)310 MHz
Input Bias Current(Max)10000000 pA
Iq per channel(Max)4.7 mA
Iq per channel(Typ)4.25 mA
Number of Channels1
Offset Drift(Typ)25 uV/C
Operating Temperature Range-40 to 85 C
Output Current(Typ)80 mA
Package GroupSOT-23
Package Size: mm2:W x L5SOT-23: 8 mm2: 2.8 x 2.9(SOT-23) PKG
Rail-to-RailIn to V-,Out
RatingCatalog
Slew Rate(Typ)600 V/us
Total Supply Voltage(Max)11 +5V=5, +/-5V=10
Total Supply Voltage(Min)2.8 +5V=5, +/-5V=10
Vn at 1kHz(Typ)9.5 nV/rtHz
Vn at Flatband(Typ)9.2 nV/rtHz
Vos (Offset Voltage @ 25C)(Max)7 mV

Öko-Plan

RoHSCompliant

Design Kits und Evaluierungsmodule

  • Evaluation Modules & Boards: DEM-OPA-SOT-1A
    Unpopulated PCB Compatible w/High Speed, Wide Bandwidth Op Amps in SOT(DBV) Pkg
    Lifecycle Status: Active (Recommended for new designs)
  • Evaluation Modules & Boards: DEM-OPA-SO-1A
    DEM-OPA-SO-1A Unpopulated PCB Compatible w/High Speed Wide Bandwidth Op Amps in 8-lead SOIC (D) Pkg
    Lifecycle Status: Active (Recommended for new designs)

Anwendungshinweise

  • RLC Filter Design for ADC Interface Applications (Rev. A)
    PDF, 299 Kb, Revision: A, Datei veröffentlicht: May 13, 2015
    As high performance Analog-to-Digital Converters (ADCs) continue to improve in their performance, the last stage interface from the final amplifier into the converter inputs becomes a critical element in the system design if the full converter dynamic range is desired. This application note describes the performance and design equations for a simple passive 2nd-order filter used successfully in AD
  • ADS5500, OPA695: PC Board Layout for Low Distortion High-Speed ADC Drivers
    PDF, 273 Kb, Datei veröffentlicht: Apr 22, 2004
    Once an analog-to-digital converter (ADC) and a driver/interface have been selected for a given application, the next step to achieving excellent performance is laying out the printed circuit board (PCB) that will support the application. This application report describes several techniques for optimizing a high-speed, 14-bit performance, differential driver PCB layout using a wideband operation
  • Wideband Complementary Current Output DAC Single-Ended Interface
    PDF, 597 Kb, Datei veröffentlicht: Jun 21, 2005
    High-speed digital-to-analog converters (DACs) most often use a transformer-coupled output stage. In applications where this configuration is not practical, a single op ampdifferential to single-ended stage has often been used. This application note steps through the exact design equations required to achieve gain matching from each output as well as a matched input impedance to each of the DA
  • Measuring Board Parasitics in High-Speed Analog Design
    PDF, 134 Kb, Datei veröffentlicht: Jul 7, 2003
    Successful circuit designs using high-speed amplifiers can depend upon understanding and identifying parasitic PCB components. Simulating a design while including PCB parasitics can protect against unpleasant production surprises. This application report discusses an easy method for measuring parasitic components in a prototype or final PC board design by using a standard oscilloscope and low freq
  • Noise Analysis for High Speed Op Amps (Rev. A)
    PDF, 256 Kb, Revision: A, Datei veröffentlicht: Jan 17, 2005
    As system bandwidths have increased an accurate estimate of the noise contribution for each element in the signal channel has become increasingly important. Many designers are not however particularly comfortable with the calculations required to predict the total noise for an op amp or in the conversions between the different descriptions of noise. Considerable inconsistency between manufactu

Modellreihe

Herstellerklassifikation

  • Semiconductors > Amplifiers > Operational Amplifiers (Op Amps) > High-Speed Op Amps (>=50MHz)