Datasheet LT1074, LT1076 (Analog Devices)

HerstellerAnalog Devices
BeschreibungStep-Down Switching Regulator
Seiten / Seite16 / 1 — FEATURES. 5A Onboard Switch (LT1074). Operates Up to 60V Input. …
Dateiformat / GrößePDF / 189 Kb
DokumentenspracheEnglisch

FEATURES. 5A Onboard Switch (LT1074). Operates Up to 60V Input. APPLICATIO S. DESCRIPTIO. TYPICAL APPLICATIO

Datasheet LT1074, LT1076 Analog Devices

Modelllinie für dieses Datenblatt

Textversion des Dokuments

LT1074/LT1076 Step-Down Switching Regulator
FEATURES
ponents, are included on the chip. The topology is a classic positive “buck” configuration but several design innova- ■
5A Onboard Switch (LT1074)
tions allow this device to be used as a positive-to-negative ■
Operates Up to 60V Input
converter, a negative boost converter, and as a flyback ■ 100kHz Switching Frequency converter. The switch output is specified to swing 40V ■ Greatly Improved Dynamic Behavior below ground, allowing the LT1074 to drive a tapped- ■ Available in Low Cost 5 and 7-Lead Packages inductor in the buck mode with output currents up to 10A. ■ Only 8.5mA Quiescent Current The LT1074 uses a true analog multiplier in the feedback ■ Programmable Current Limit loop. This makes the device respond nearly instanta- ■ Micropower Shutdown Mode neously to input voltage fluctuations and makes loop gain
U
independent of input voltage. As a result, dynamic behav-
APPLICATIO S
ior of the regulator is significantly improved over previous designs. ■ Buck Converter with Output Voltage Range of 2.5V to 50V On-chip pulse by pulse current limiting makes the LT1074 ■ Tapped-Inductor Buck Converter with 10A Output nearly bust-proof for output overloads or shorts. The input at 5V voltage range as a buck converter is 8V to 60V, but a self- ■ Positive-to-Negative Converter boot feature allows input voltages as low as 5V in the ■ Negative Boost Converter inverting and boost configurations. ■ Multiple Output Buck Converter The LT1074 is available in low cost TO-220 or DD packages
U
with frequency pre-set at 100kHz and current limit at 6.5A
DESCRIPTIO
(LT1076 = 2.6A). A 7-pin TO-220 package is also available which allows current limit to be adjusted down to zero. In The LT®1074 is a 5A (LT1076 is rated at 2A) monolithic addition, full micropower shutdown can be programmed. bipolar switching regulator which requires only a few See Application Note 44 for design details. external parts for normal operation. The power switch, all A fixed 5V output, 2A version is also available. See LT1076-5. oscillator and control circuitry, and all current limit com- , LTC and LT are registered trademarks of Linear Technology Corporation.
U TYPICAL APPLICATIO Buck Converter Efficiency Basic Positive Buck Converter
LT1074 100 L1** 50µH (LT1074) V = 12V, V = 20V OUT IN 100µH (LT1076) 90 5V V V IN SW 5A 10V TO 40V * USE MBR340 FOR LT1076 ** COILTRONICS #50-2-52 (LT1074) 80 LT1074 R1 MBR745* 2.8k #100-1-52 (LT1076) V = 5V, V = 15V OUT IN 1% PULSE ENGINEERING, INC. EFFICIENCY (%) FB 70 GND V #PE-92114 (LT1074) C #PE-92102 (LT1076) R2 R3 60 L = 50µH TYPE 52 CORE 2.21k HURRICANE #HL-AK147QQ (LT1074) 2.7k DIODE = MBR735 + 1% + #HL-AG210LL (LT1076) C3† C2 C1 † RIPPLE CURRENT RATING ≥ IOUT/2 50 200µF 0.01µF 500µF 0 1 2 3 4 5 6 25V OUTPUT LOAD CURRENT (A) LT1074•TA01 LT1074•TPC27 sn1074 1074fds 1