Datasheet LTC4306 (Analog Devices) - 3

HerstellerAnalog Devices
Beschreibung4-Channel, 2-Wire Bus Multiplexer with Capacitance Buffering
Seiten / Seite20 / 3 — ELECTRICAL CHARACTERISTICS The
Dateiformat / GrößePDF / 275 Kb
DokumentenspracheEnglisch

ELECTRICAL CHARACTERISTICS The

ELECTRICAL CHARACTERISTICS The

Modelllinie für dieses Datenblatt

Textversion des Dokuments

LTC4306
ELECTRICAL CHARACTERISTICS The

denotes specifications which apply over the full specified temperature range, otherwise specifications are at TA = 25
°
C. VCC = 3.3V unless otherwise noted. SYMBOL PARAMETER CONDITIONS MIN TYP MAX UNITS
VUVLOHYST UVLO Threshold Hysteresis Voltage ● 100 175 250 mV VTH EN ENABLE Falling Threshold Voltage ● 0.8 1.0 1.2 V VENHYST ENABLE Threshold Hysteresis Voltage 60 mV tPHLEN ENABLE Delay, On-Off 60 ns tPLHEN ENABLE Delay, Off-On 20 ns IINEN ENABLE Input Leakage Current VENABLE = 0V, 5.5V, VCC = 5.5V ● 0 ±1 µA VLOWREADY READY Pin Logic Low Output Voltage IPULL-UP = 3mA, VCC = 2.7V ● 0.18 0.4 V IOFFREADY READY Off State Input Leakage Current VREADY = 0V, 5.5V, VCC = 5.5V ● 0 ±1 µA
Upstream-Downstream Buffers
VOS,BUF Buffer Offset Voltage RBUS = 10k, VCC = 2.7V, 5.5V (Note 4) ● 25 60 100 mV VOS,UP-BUF Upstream Buffer Offset Voltage VCC = 2.7V, RBUS = 2.7k (Note 4) ● 40 80 120 mV VIN, BUFFER = 0V VCC = 5.5V, RBUS = 2.7k (Note 4) ● 70 110 150 mV VOS,DOWN-BUF Downstream Buffer Offset Voltage VCC = 2.7V, RBUS = 2.7k (Note 4) ● 60 110 160 mV VIN, BUFFER = 0V VCC = 5.5V, RBUS = 2.7k (Note 4) ● 80 140 200 mV VOL Output Low Voltage, VIN,BUFFER = 0V SDA, SCL Pins; ISINK = 4mA, ● 400 mV VCC = 3V, 5.5V Output Low Voltage, VIN,BUFFER = 0.2V SDA, SCL Pins; ISINK = 500µA, ● 320 mV VCC = 2.7V, 5.5V VIL,MAX Buffer Input Logic Low Voltage VCC = 2.7V, 5.5V ● 0.4 0.52 0.64 V VTHSDA,SCL Downstream SDA, SCL Logic Threshold Voltage ● 0.8 1.0 1.2 V ILEAK Input Leakage Current SDA, SCL Pins; VCC = 0V to 5.5V; ● 0 ±5 µA Buffers Inactive
Rise Time Accelerators
VSDA,SCL slew Minimum Slew Requirement to Activate SDAIN, SCLIN, SDA1-4, SCL1-4 Pins ● 0.4 0.8 V/µs Rise Time Accelerator Currents VRISE,DC Rise Time Accelerator DC Threshold Voltage SDAIN, SCLIN, SDA1-4, SCL1-4 Pins ● 0.7 0.8 1 V IBOOST Rise Time Accelerator Pull-Up Current SDAIN, SCLIN, SDA1-4, SCL1-4 Pins 4 5.5 mA (Note 3)
GPIOs
VGPIO(TH) GPIO Pin Input Threshold ● 0.8 1 1.2 V VGPIO(OL) GPIO Pin Output Low Voltage IGPIO = 5mA, VCC = 2.7V ● 0.2 0.4 V VGPIO(OH) GPIO Pin Output High Voltage IGPIO = –200µA, VCC = 2.7V ● VCC – 0.3 V IGPIO(IN) GPIO Pin Input Leakage Current VGPIO = 0V, 5.5V, VCC = 5.5V ● 0 ±1 µA
Stuck Low Timeout Circuitry
VTIMER(L) Stuck Low Falling Threshold Voltage VCC = 2.7V, 5.5V ● 0.4 0.52 0.64 V VTIMER(HYST) Stuck Low Threshold Hysteresis Voltage 80 mV TTIMER1 Timeout Time #1 TIMSET1,0 = 01 ● 25 30 35 ms TTIMER2 Timeout Time #2 TIMSET1,0 = 10 ● 12.5 15 17.5 ms TTIMER3 Timeout Time #3 TIMSET1,0 = 11 ● 6.25 7.5 8.75 ms
ALERT
VALERT(OL) ALERT Output Low Voltage IALERT = 3mA, VCC = 2.7V ● 0.2 0.4 V IOFF,ALERT ALERT Off State Input Leakage Current VALERT = 0V, 5.5V ● 0 ±1 µA IIN,ALERT1-4 ALERT1-ALERT4 Input Current VALERT1-4 = 0V, 5.5V ● 0 ±1 µA 4306f 3