Datasheet LTC6900 (Analog Devices) - 3

HerstellerAnalog Devices
BeschreibungLow Power, 1kHz to 20MHz Resistor Set SOT-23 Oscillator
Seiten / Seite12 / 3 — ELECTRICAL CHARACTERISTICS. The. denotes the specifi cations which apply …
Dateiformat / GrößePDF / 164 Kb
DokumentenspracheEnglisch

ELECTRICAL CHARACTERISTICS. The. denotes the specifi cations which apply over the full operating

ELECTRICAL CHARACTERISTICS The denotes the specifi cations which apply over the full operating

Modelllinie für dieses Datenblatt

Textversion des Dokuments

LTC6900
ELECTRICAL CHARACTERISTICS The
l
denotes the specifi cations which apply over the full operating temperature range, otherwise specifi cations are at TA = 25°C. V+ = 2.7V to 5.5V, RL= 5k, CL = 5pF, Pin 4 = V + unless otherwise noted. All voltages are with respect to GND. SYMBOL PARAMETER CONDITIONS MIN TYP MAX UNITS
V+ Operating Supply Range ● 2.7 5.5 V IS Power Supply Current RSET = 400k, Pin 4 = V+, RL = ∞ V+ = 5V ● 0.32 0.42 mA fOSC = 5kHz V+ = 3V ● 0.29 0.38 mA RSET = 20k, Pin 4 = 0V, RL = ∞ V+ = 5V ● 0.92 1.20 mA fOSC = 10MHz V+ = 3V ● 0.68 0.86 mA VIH High Level DIV Input Voltage ● V+ – 0.4 V VIL Low Level DIV Input Voltage ● 0.5 V IDIV DIV Input Current (Note 5) Pin 4 = V+ V+ = 5V ● 2 4 μA Pin 4 = 0V V+ = 5V ● – 4 –2 μA VOH High Level Output Voltage (Note 5) V+ = 5V IOH = – 1mA ● 4.8 4.95 V IOH = –4mA ● 4.5 4.8 V V+ = 3V IOH = – 1mA ● 2.7 2.9 V IOH = –4mA ● 2.2 2.6 V VOL Low Level Output Voltage (Note 5) V+ = 5V IOL = 1mA ● 0.05 0.15 V IOL = 4mA ● 0.2 0.4 V V+ = 3V IOL = 1mA ● 0.1 0.3 V IOL = 4mA ● 0.4 0.7 V tr OUT Rise Time V+ = 5V Pin 4 = V+ or Floating, RL = ∞ 14 ns (Note 6) Pin 4 = 0V, RL = ∞ 7 ns V+ = 3V Pin 4 = V+ or Floating, RL = ∞ 19 ns Pin 4 = 0V, RL = ∞ 11 ns tf OUT Fall Time V+ = 5V Pin 4 = V+ or Floating, RL = ∞ 13 ns (Note 6) Pin 4 = 0V, RL = ∞ 6 ns V+ = 3V Pin 4 = V+ or Floating, RL = ∞ 19 ns Pin 4 = 0V, RL = ∞ 10 ns
Note 1:
Stresses beyond those listed under Absolute Maximum Ratings
Note 5:
To conform with the Logic IC Standard convention, current out of may cause permanent damage to the device. Exposure to any Absolute a pin is arbitrarily given as a negative value. Maximum Rating condition for extended periods may affect device
Note 6:
Output rise and fall times are measured between the 10% and 90% reliability and lifetime. power supply levels. These specifi cations are based on characterization.
Note 2:
Frequencies near 100kHz and 1MHz may be generated using two
Note 7:
Guaranteed by 5V test. different values of RSET (see the Selecting the Divider Setting Resistor
Note 8:
The LTC6900C is guaranteed to meet specifi ed performance from paragraph in the Applications Information section). For these frequencies, 0°C to 70°C. The LTC6900C is designed, characterized and expected to the error is specifi ed under the following assumption: 20k < RSET ≤ 200k. meet specifi ed performance from – 40°C to 85°C but is not tested or
Note 3:
Frequency accuracy is defi ned as the deviation from the QA sampled at these temperatures. The LTC6900I is guaranteed to meet fOSC equation. specifi ed performance from –40°C to 85°C.
Note 4:
Jitter is the ratio of the peak-to-peak distribution of the period to the mean of the period. This specifi cation is based on characterization and is not 100% tested. Also, see the Peak-to-Peak Jitter vs Output Frequency curve in the Typical Performance Characteristics section. 6900fa 3