Datasheet Texas Instruments LM5022 — Datenblatt
| Hersteller | Texas Instruments |
| Serie | LM5022 |
6-60V Wide Vin, Current Mode Boost und SEPIC Controller
Datenblätter
LM5022 60-V Low-Side Controller for Boost and SEPIC datasheet
PDF, 1.5 Mb, Revision: H, Datei veröffentlicht: Dec 16, 2016
Auszug aus dem Dokument
Preise
Status
| LM5022MM | LM5022MM/NOPB | LM5022MME/NOPB | LM5022MMX/NOPB | |
|---|---|---|---|---|
| Lifecycle Status | NRND (Not recommended for new designs) | Active (Recommended for new designs) | Active (Recommended for new designs) | Active (Recommended for new designs) |
| Manufacture's Sample Availability | No | Yes | No | No |
Verpackung
| LM5022MM | LM5022MM/NOPB | LM5022MME/NOPB | LM5022MMX/NOPB | |
|---|---|---|---|---|
| N | 1 | 2 | 3 | 4 |
| Pin | 10 | 10 | 10 | 10 |
| Package Type | DGS | DGS | DGS | DGS |
| Industry STD Term | VSSOP | VSSOP | VSSOP | VSSOP |
| JEDEC Code | S-PDSO-G | S-PDSO-G | S-PDSO-G | S-PDSO-G |
| Package QTY | 1000 | 1000 | 250 | 3500 |
| Carrier | SMALL T&R | SMALL T&R | SMALL T&R | LARGE T&R |
| Device Marking | 5022 | 5022 | 5022 | 5022 |
| Width (mm) | 3 | 3 | 3 | 3 |
| Length (mm) | 3 | 3 | 3 | 3 |
| Thickness (mm) | 1.02 | 1.02 | 1.02 | 1.02 |
| Pitch (mm) | .5 | .5 | .5 | .5 |
| Max Height (mm) | 1.07 | 1.07 | 1.07 | 1.07 |
| Mechanical Data | Herunterladen | Herunterladen | Herunterladen | Herunterladen |
Parameter
| Parameters / Models | LM5022MM | LM5022MM/NOPB | LM5022MME/NOPB | LM5022MMX/NOPB |
|---|---|---|---|---|
| Duty Cycle(Max), % | 90 | 90 | 90 | 90 |
| Iout(Max), A | 10 | 10 | 10 | 10 |
| Iq(Typ), mA | 3.5 | 3.5 | 3.5 | 3.5 |
| Operating Temperature Range, C | -40 to 125 | -40 to 125 | -40 to 125 | -40 to 125 |
| Package Group | VSSOP | VSSOP | VSSOP | VSSOP |
| Rating | Catalog | Catalog | Catalog | Catalog |
| Regulated Outputs | 1 | 1 | 1 | 1 |
| Special Features | Enable,Frequency Synchronization,UVLO Adjustable | Enable,Frequency Synchronization,UVLO Adjustable | Enable,Frequency Synchronization,UVLO Adjustable | Enable,Frequency Synchronization,UVLO Adjustable |
| Switch Current Limit(Typ), A | 10 | 10 | 10 | 10 |
| Switching Frequency(Max), kHz | 1000 | 1000 | 1000 | 1000 |
| Switching Frequency(Min), kHz | 170 | 170 | 170 | 170 |
| Type | Controller | Controller | Controller | Controller |
| Vin(Max), V | 60 | 60 | 60 | 60 |
| Vin(Min), V | 6 | 6 | 6 | 6 |
| Vout(Max), V | 300 | 300 | 300 | 300 |
| Vout(Min), V | 1.25 | 1.25 | 1.25 | 1.25 |
Öko-Plan
| LM5022MM | LM5022MM/NOPB | LM5022MME/NOPB | LM5022MMX/NOPB | |
|---|---|---|---|---|
| RoHS | See ti.com | Compliant | Compliant | Compliant |
Anwendungshinweise
- AN-1696 Designing a Boost LED Driver Using the LM5022 (Rev. B)PDF, 238 Kb, Revision: B, Datei veröffentlicht: May 6, 2013
This application report provides a component-by-component design guide for a boost converter-basedLED driver using the LM5022. - Driving LEDs: To Cap or Not to CapPDF, 542 Kb, Datei veröffentlicht: Mar 21, 2007
- Demystifying Type II and Type III Compensators Using Op-Amp and OTA for DC/DC CoPDF, 782 Kb, Datei veröffentlicht: Jul 11, 2014
- AN-1656 Design Challenges of Switching LED Drivers (Rev. A)PDF, 171 Kb, Revision: A, Datei veröffentlicht: May 3, 2013
Using a switching regulator as an LED driver requires the designer to convert a voltage regulator into acurrent regulator. Beyond the challenge of changing the feedback system to control current, the LEDsthemselves present a load characteristic that is much different than the digital devices and other loads thatrequire constant voltage. The LED WEBENCHВ® online design environment predicts and
Modellreihe
Serie: LM5022 (4)
Herstellerklassifikation
- Semiconductors> Power Management> Non-isolated DC/DC Switching Regulator> Step-Up (Boost)> Boost Controller (External Switch)