Datasheet Texas Instruments LM46000 — Datenblatt

HerstellerTexas Instruments
SerieLM46000
Datasheet Texas Instruments LM46000

SIMPLE SWITCHER® 3.5 - 60V, 500mA Synchroner Abwärtsspannungswandler

Datenblätter

LM46000 SIMPLE SWITCHER 3.5 V to 60 V 0.5 A Synchronous Step-Down Voltage Converter datasheet
PDF, 2.5 Mb, Revision: A, Datei veröffentlicht: Jul 11, 2014
Auszug aus dem Dokument

Preise

Status

LM46000PWPLM46000PWPRLM46000PWPT
Lifecycle StatusActive (Recommended for new designs)Active (Recommended for new designs)Active (Recommended for new designs)
Manufacture's Sample AvailabilityNoNoYes

Verpackung

LM46000PWPLM46000PWPRLM46000PWPT
N123
Pin161616
Package TypePWPPWPPWP
Industry STD TermHTSSOPHTSSOPHTSSOP
JEDEC CodeR-PDSO-GR-PDSO-GR-PDSO-G
Package QTY902000250
CarrierTUBELARGE T&RSMALL T&R
Device MarkingLM46000LM46000LM46000
Width (mm)4.44.44.4
Length (mm)555
Thickness (mm)111
Pitch (mm).65.65.65
Max Height (mm)1.21.21.2
Mechanical DataHerunterladenHerunterladenHerunterladen

Parameter

Parameters / ModelsLM46000PWP
LM46000PWP
LM46000PWPR
LM46000PWPR
LM46000PWPT
LM46000PWPT
Control ModeCurrent ModeCurrent ModeCurrent Mode
Duty Cycle(Max), %999999
Iout(Max), A0.50.50.5
Iq(Typ), mA0.0240.0240.024
Operating Temperature Range, C-40 to 125-40 to 125-40 to 125
Package GroupHTSSOPHTSSOPHTSSOP
RatingCatalogCatalogCatalog
Regulated Outputs111
Special FeaturesEnable,Frequency Synchronization,Light Load Efficiency,Power Good,Synchronous Rectification,TrackingEnable,Frequency Synchronization,Light Load Efficiency,Power Good,Synchronous Rectification,TrackingEnable,Frequency Synchronization,Light Load Efficiency,Power Good,Synchronous Rectification,Tracking
Switching Frequency(Max), kHz220022002200
Switching Frequency(Min), kHz200200200
TypeConverterConverterConverter
Vin(Max), V606060
Vin(Min), V3.53.53.5
Vout(Max), V282828
Vout(Min), V111

Öko-Plan

LM46000PWPLM46000PWPRLM46000PWPT
RoHSCompliantCompliantCompliant

Anwendungshinweise

  • Compensation Made SIMPLE With LM4360x, LM4600x
    PDF, 457 Kb, Datei veröffentlicht: Jul 29, 2014
    Compensating a DC-DC buck converter is challenging if the designer is not familiar with the loop control theory. To achieve a stable design under all corner and adverse conditions, the user must properly compensate the regulator. While DC-DC converters with external compensation provide flexibility, they increase complexity. The LM43600/1/2/3 and LM46000/1/2 are a family of Wide VIN, fully-synchro
  • Inverting Applications Made SIMPLE With LM4600x and LM4360x (Rev. B)
    PDF, 1.9 Mb, Revision: B, Datei veröffentlicht: Feb 20, 2015
    Weoftenrequirepowersourceswithnegativeoutputvoltages.Therearemanydifferentwaystoproduceanegativeoutputvoltagefromapositiveinputvoltage.Oneoptionisapolarity-invertingbuck-boostconverter.Theadvantagesofthistopologyarethatitrequireslowcomponentcountandthatitcanbebuiltwithstandardhigh-sideregulato
  • Thermal Design Made Simple With LM43603 and LM46002
    PDF, 535 Kb, Datei veröffentlicht: Sep 15, 2014
    This Application Report will walk through the thermal design of power supplies using the LM43603 and LM46002.In the process we will cover common tips and approximations to speed up your design.
  • Cap Drop Offline Supply for E-Meters
    PDF, 291 Kb, Datei veröffentlicht: Jun 16, 2015
    This design idea provides a simple non-isolated AC/DC power supply for low power applications such assmart grid E-meter applications. The design uses a "capacitive-dropper" front-end combined with aLM46000 SIMPLE SWITCHERВ® buck regulator from Texas Instruments. The circuit provides 3.3 V at aminimum of 50 mA from a line supply of 90 VAC to 265 VAC. Theory of operation as well as designequa
  • Cost-Effective Transformerless Offline Supply for Light Load Applications (Rev. A)
    PDF, 295 Kb, Revision: A, Datei veröffentlicht: Jun 16, 2015
    This design idea provides a simple non-isolated AC/DC power supply for low power applications. Thedesign uses a "capacitive-dropper" front-end combined with a LM46000 SIMPLE SWITCHERВ® buckregulator from Texas Instruments. The circuit provides 3.3 V at a minimum of 100 mA from a line supply of90 VAC to 265 VAC. Theory of operation as well as design equations and performance results are given.
  • AN-1533 Overvoltage Protection Circuit for Automotive Load Dump (Rev. B)
    PDF, 83 Kb, Revision: B, Datei veröffentlicht: May 6, 2013
    This application report discusses an over voltage protection circuit for automotive load dump.
  • Understanding and Applying Current-Mode Control Theory
    PDF, 409 Kb, Datei veröffentlicht: Aug 19, 2007
  • AN-1997 Error Amplifier Limitations in High-Performance Regulator Applications (Rev. A)
    PDF, 153 Kb, Revision: A, Datei veröffentlicht: May 6, 2013
    The development of realistic predictions to assist the power supply engineer during the control loop design process is facilitated in this application report by appropriate small-signal and bode plot analysis, the validity of which is verified through simulation results.
  • AN-1246 Stresses in Wide Input DC-DC Converters (Rev. C)
    PDF, 427 Kb, Revision: C, Datei veröffentlicht: Apr 23, 2013
    This application note discusses stresses in wide input DC-DC converters.
  • Low EMI Layout Made SIMPLE With LM43600/1/2/3 and LM46000/1/2 (Rev. A)
    PDF, 512 Kb, Revision: A, Datei veröffentlicht: Sep 12, 2014
    Printed Circuit Board (PCB) layout for Switched Mode Power Supplies (SMPS) is critical to achieve proper converter operation good thermal performance and excellent radiated EMI performance. Optimized board layout for low radiated EMI is made very simple by the package and pin arrangement of the SIMPLE SWITCHER Synchronous Buck Converter family LM4360x and LM4600x
  • Understanding Buck-Boost Power Stages in Switchmode Power Supplies (Rev. A)
    PDF, 363 Kb, Revision: A, Datei veröffentlicht: May 28, 2002
  • AN-1197 Selecting Inductors for Buck Converters (Rev. B)
    PDF, 558 Kb, Revision: B, Datei veröffentlicht: Apr 23, 2013
    This application report provides design information to help select an off-the-shelf inductor for anycontinuous-mode buck converter application.
  • AN-1566 Techniques for Thermal Analysis of Switching Power Supply Designs (Rev. A)
    PDF, 1.4 Mb, Revision: A, Datei veröffentlicht: Apr 23, 2013
    This application note provides thermal power analysis techniques for analyzing the power IC.
  • AN-1889 How to Measure the Loop Transfer Function of Power Supplies (Rev. A)
    PDF, 2.7 Mb, Revision: A, Datei veröffentlicht: Apr 23, 2013
    This application report shows how to measure the critical points of a bode plot with only an audiogenerator (or simple signal generator) and an oscilloscope. The method is explained in an easy to followstep-by-step manner so that a power supply designer can start performing these measurements in a shortamount of time.
  • AN-643 EMI/RFI Board Design (Rev. B)
    PDF, 742 Kb, Revision: B, Datei veröffentlicht: May 3, 2004
    Application Note 643 EMI/RFI Board Design
  • AN-1149 Layout Guidelines for Switching Power Supplies (Rev. C)
    PDF, 82 Kb, Revision: C, Datei veröffentlicht: Apr 23, 2013
    When designing a high frequency switching regulated power supply layout is very important. Using agood layout can solve many problems associated with these types of supplies. The problems due to a badlayout are often seen at high current levels and are usually more obvious at large input to output voltagedifferentials. Some of the main problems are loss of regulation at high output current
  • AN-1520 A Guide to Board Layout for Best Thermal Resistance for Exposed Packages (Rev. B)
    PDF, 9.2 Mb, Revision: B, Datei veröffentlicht: Apr 23, 2013
    This thermal application report provides guidelines for the optimal board layout to achieve the best thermalresistance for exposed packages. The thermal resistance between junction-to-ambient (ОёJA) is highlydependent on the PCB (Printed Circuit Board) design factors. This becomes more critical for packageshaving very low thermal resistance between junction-to-case such as exposed pad TSSOP
  • AN-2155 Layout Tips for EMI Reduction in DC/ DC Converters (Rev. A)
    PDF, 3.6 Mb, Revision: A, Datei veröffentlicht: Apr 23, 2013
    This application note will explore how the layout of your DC/DC power supply can significantly affect theamount of EMI that it produces. It will discuss several variations of a layout analyze the results andprovide answers to some common EMI questions such whether or not to use a shielded inductor.
  • AN-1229 SIMPLE SWITCHER PCB Layout Guidelines (Rev. C)
    PDF, 374 Kb, Revision: C, Datei veröffentlicht: Apr 23, 2013
    This application report provides SIMPLE SWITCHER™ PCB layout guidelines.
  • AN-2162 Simple Success With Conducted EMI From DC-DC Converters (Rev. C)
    PDF, 2.5 Mb, Revision: C, Datei veröffentlicht: Apr 24, 2013
    Electromagnetic Interference (EMI) is an unwanted effect between two electrical systems as a result ofeither electromagnetic radiation or electromagnetic conduction. EMI is the major adverse effect caused bythe application of switch-mode power supplies (SMPS). In switching power supplies EMI noise isunavoidable due to the switching actions of the semiconductor devices and resulting disconti
  • Semiconductor and IC Package Thermal Metrics (Rev. C)
    PDF, 201 Kb, Revision: C, Datei veröffentlicht: Apr 19, 2016
  • Input and Output Capacitor Selection
    PDF, 219 Kb, Datei veröffentlicht: Sep 19, 2005

Modellreihe

Herstellerklassifikation

  • Semiconductors> Power Management> Non-isolated DC/DC Switching Regulator> Step-Down (Buck)> Buck Converter (Integrated Switch)