Datasheet Texas Instruments CDCE906PWG4 — Datenblatt

HerstellerTexas Instruments
SerieCDCE906
ArtikelnummerCDCE906PWG4
Datasheet Texas Instruments CDCE906PWG4

Programmierbarer 3-PLL-Taktsynthesizer / Multiplikator / Teiler 20-TSSOP 0 bis 70

Datenblätter

Programmable 3-PLL Clock Synthesizer / Multiplier/Divider datasheet
PDF, 1.7 Mb, Revision: H, Datei veröffentlicht: Dec 11, 2007
Auszug aus dem Dokument

Preise

Status

Lifecycle StatusActive (Recommended for new designs)
Manufacture's Sample AvailabilityYes

Verpackung

Pin20
Package TypePW
Industry STD TermTSSOP
JEDEC CodeR-PDSO-G
Package QTY70
CarrierTUBE
Device MarkingCDCE906
Width (mm)4.4
Length (mm)6.5
Thickness (mm)1
Pitch (mm).65
Max Height (mm)1.2
Mechanical DataHerunterladen

Parameter

Divider RatioUniversal
FunctionClock Synthesizer,Clock Multiplier,Clock Divider
Input LevelCrystal,LVCMOS,Differential
Jitter-Peak to Peak(P-P) or Cycle to Cycle60 ps C-C
Operating Temperature Range0 to 70 C
Output Frequency(Max)167 MHz
Output LevelLVCMOS
Output Skew150 ps
Package GroupTSSOP
Package Size: mm2:W x L20TSSOP: 42 mm2: 6.4 x 6.5(TSSOP) PKG
RatingCatalog
Special FeaturesIntegrated EEPROM,Multiplier/Divider,Spread Spectrum Clocking (SSC)
VCC3.3 V

Öko-Plan

RoHSCompliant

Design Kits und Evaluierungsmodule

  • Evaluation Modules & Boards: CDCE906-706PROGEVM
    CDCE906 and CDCE706 programmable EVM
    Lifecycle Status: Active (Recommended for new designs)
  • Evaluation Modules & Boards: CDCE906-706PERFEVM
    CDCE906 and CDCE706 EVM
    Lifecycle Status: Active (Recommended for new designs)

Anwendungshinweise

  • Recommended Terminations for the Differential Inputs of CDCE906/CDCE706
    PDF, 84 Kb, Datei veröffentlicht: Aug 10, 2006
    This application report describes how differential signals (LVDS, LVPECL, and HSTL) can be connected to CDCE706/CDCE906 differential inputs directly. The wide common-mode voltage and smaller swing required make the devices so versatile that they can receive any signal without any complicated coupling and biasing circuits.
  • CDCx706/x906 Termination and Signal Integrity Guidelines (Rev. A)
    PDF, 155 Kb, Revision: A, Datei veröffentlicht: Nov 28, 2007
    This application report shows and evaluates different schemes for the CDCE706, CDCE906, CDC706, and CDC906. Guidelines for optimizing the series termination are discussed. Additionally, this report describes how the CDCx706/x906 family can be used to drive 1.8-V clock inputs.
  • High Speed Layout Guidelines (Rev. A)
    PDF, 762 Kb, Revision: A, Datei veröffentlicht: Aug 8, 2017
    Thisapplicationreportaddresseshigh-speedsignals,suchas clocksignalsand theirrouting,and givesdesignersa reviewof the importantcoherences.Withsomesimplerules,electromagneticinterferenceproblemscan be minimizedwithoutusingcomplicatedformulasand expensivesimulationtools.Section1givesa shortintroductionto theory,whileSection
  • Clock Recommendations for the DM643x EVM
    PDF, 121 Kb, Datei veröffentlicht: Nov 29, 2006
    The DM643x evaluation module (EVM) requires several clock frequencies to run the system properly. The current clocking proposal of the low-cost EVM consists of the VCXO chip PI6CX100-27W, the PLL chip PLL1705, several bus drivers, and a few oscillaors and crystals. This application report discusses several optimized clocking proposals with the Texas Instruments new clock drivers and recommends a m
  • Troubleshooting I2C Bus Protocol
    PDF, 184 Kb, Datei veröffentlicht: Oct 19, 2009
    When using the I2Cв„ў bus protocol, the designer must ensure that the hardware complies with the I2C standard. This application report describes the I2C protocol and provides guidelines on debugging a missing acknowledgment, selecting the pullup resistors, or meeting the maximum capacitance load of an I2C bus. A conflict occurs if devices sharing the I2C bus have the same slave address. This

Modellreihe

Herstellerklassifikation

  • Semiconductors > Clock and Timing > Clock Generators > Spread-Spectrum Clocks