Datasheet Texas Instruments OPA128KM — Datenblatt

HerstellerTexas Instruments
SerieOPA128
ArtikelnummerOPA128KM
Datasheet Texas Instruments OPA128KM

Difet Electrometer-Operationsverstärker 8-TO-99 -55 bis 125

Datenblätter

Datasheet OPA128
PDF, 138 Kb, Datei veröffentlicht: Sep 27, 2000, Seiten: 11
Difet Electrometer-Grade Operational Amplifier
Auszug aus dem Dokument

Preise

Status

Lifecycle StatusActive (Recommended for new designs)
Manufacture's Sample AvailabilityYes

Verpackung

Pin8
Package TypeLMC
Industry STD TermTO-CAN
JEDEC CodeO-MBCY-W
Package QTY20
CarrierTUBE
Device MarkingOPA128KM
Width (mm)9.08
Length (mm)9.08
Thickness (mm)4.4
Pitch (mm)2.54
Max Height (mm)5.72
Mechanical DataHerunterladen

Parameter

Additional FeaturesN/A
ArchitectureFET
CMRR(Min)80 dB
CMRR(Typ)118 dB
GBW(Typ)1 MHz
Input Bias Current(Max)0.075 pA
Iq per channel(Max)1.8 mA
Iq per channel(Typ)0.9 mA
Number of Channels1
Offset Drift(Typ)5 uV/C
Operating Temperature Range-55 to 125 C
Output Current(Typ)34 mA
Package GroupTO-99
Package Size: mm2:W x L8TO-99: 80 mm2: 8.96 x 8.96(TO-99) PKG
Rail-to-RailOut
RatingCatalog
Slew Rate(Typ)3 V/us
Total Supply Voltage(Max)36 +5V=5, +/-5V=10
Total Supply Voltage(Min)10 +5V=5, +/-5V=10
Vn at 1kHz(Typ)27 nV/rtHz
Vos (Offset Voltage @ 25C)(Max)0.5 mV

Öko-Plan

RoHSCompliant

Anwendungshinweise

  • Designing Photodiode Amplifier Circuits with OPA128
    PDF, 76 Kb, Datei veröffentlicht: Oct 2, 2000
    The OPA128 ultra-low bias current operational amplifier achieves its 75fA maximum bias current without compromise. Using standard design techniques, serious performance trade-offs were required which sacrificed overall amplifier performance in order to reach femtoamp (fA = 10-15A) bias currents.
  • Diode-Connected FET Protects Op Amps
    PDF, 49 Kb, Datei veröffentlicht: Oct 2, 2000
    Providing input-overload protection for sensitive measurement circuits proves difficult when you must not degrade the circuits? performance in the process. It?s an especially tricky problem when you?re measuring a material?s dielectric properties. In such an application, an ultra-low input bias current op amp serves as a current integrator to measure a dielectric?s response to a 100V step.
  • Boost Instrument Amp CMR With Common-Mode Driven Supplies
    PDF, 175 Kb, Datei veröffentlicht: Sep 27, 2000
    Ever-increasing demands are being placed on instrumentation amplifier (IA) performance. When standard IAs can not deliver the required performance, consider this enhanced version. Dramatic performance improvements can be achieved by operating the input amplifiers of a classical three-op-amp IA from common-mode driven sub-regulated power supplies.
  • Comparison of Noise Performance of FET Transimpedence Amp/Switched Integrator
    PDF, 66 Kb, Datei veröffentlicht: Sep 27, 2000
    Low-input current FET operational amplifiers are universlly used to monitor photodetector, or more commonly photodiode currents. These photodetectors bridge the gap between a physical event, light, and electronics. There are a variey of amplifier configurations to select from and the choice is based on noise, bandwidth, offset, and linearity. A considerable amount has been written on the performan
  • Compensate Transimpedance Amplifiers Intuitively (Rev. A)
    PDF, 69 Kb, Revision: A, Datei veröffentlicht: Mar 30, 2005
    Transimpedance amplifiers are used to convert low-level photodiode currents to usable voltage signals. All too often, the amplifiers have to be empirically compensated to operate properly. The problem can be easily understood if one looks at all the elements involved.
  • Tuning in Amplifiers
    PDF, 44 Kb, Datei veröffentlicht: Oct 2, 2000
    Have you ever had the experience of designing an analog gain block with an amplifier that is specified to be unity gain stable only to find that it is oscillating out of control in your circuit? Or have you ever replaced a stable voltage feedback amplifier with a current feedback amplifier to find that the current feedback amplifier immediately oscillates when placed in the amplifier socket? Oscil
  • Single-Supply Operation of Operational Amplifiers
    PDF, 77 Kb, Datei veröffentlicht: Oct 2, 2000
    Operation of op amps from single supply voltages is useful when negative supply voltages are not available. Furthermore, certain applications using high voltage and high current op amps can derive important benefits from single supply operation.
  • Op Amp Performance Analysis
    PDF, 76 Kb, Datei veröffentlicht: Oct 2, 2000
    This bulletin reflects the analysis power gained through knowledge of an op amp circuit's feedback factor. Feedback dictates the performance of an op amp both in function and in quality. The major specifications of the amplifier descibe an open-loop device awaiting feedback direction of the end circuit's function. Just how well the amplifier performs the function reflects through the feedback inte

Modellreihe

Serie: OPA128 (4)

Herstellerklassifikation

  • Semiconductors > Amplifiers > Operational Amplifiers (Op Amps) > Precision Op Amps