Datasheet Texas Instruments LM2576T-ADJ — Datenblatt

HerstellerTexas Instruments
SerieLM2576
ArtikelnummerLM2576T-ADJ
Datasheet Texas Instruments LM2576T-ADJ

SIMPLE SWITCHER® 40V, 3A Abwärtsregler mit niedriger Komponentenzahl 5-TO-220 -40 bis 125

Datenblätter

LM2576xx Series SIMPLE SWITCHER 3-A Step-Down Voltage Regulator datasheet
PDF, 4.5 Mb, Revision: D, Datei veröffentlicht: May 27, 2016
Auszug aus dem Dokument

Preise

Status

Lifecycle StatusNRND (Not recommended for new designs)
Manufacture's Sample AvailabilityNo

Verpackung

Pin5
Package TypeKC
Industry STD TermTO-220
JEDEC CodeR-PSFM-T
Package QTY45
CarrierTUBE
Width (mm)8.51
Length (mm)10.16
Thickness (mm)4.58
Pitch (mm)1.7
Max Height (mm)4.7
Mechanical DataHerunterladen

Ersatz

ReplacementLM2576T-ADJ/NOPB
Replacement CodeS

Parameter

Control ModeVoltage Mode
Duty Cycle(Max)98 %
FeaturesEnable
Iout(Max)3 A
Iq(Typ)5 mA
Operating Temperature Range-40 to 125 C
Package GroupTO-220
RatingCatalog
Regulated Outputs1
Switching Frequency(Max)63 kHz
Switching Frequency(Min)42 kHz
TypeConverter
Vin(Max)40 V
Vin(Min)4 V
Vout(Max)37 V
Vout(Min)3.3 V

Öko-Plan

RoHSSee ti.com

Design Kits und Evaluierungsmodule

  • Evaluation Modules & Boards: LM2576S-ADJEVM
    LM2576 Step-Down Converter Evaluation Module
    Lifecycle Status: Active (Recommended for new designs)

Anwendungshinweise

  • High-Efficiency 3A Battery Chargers Use LM2576 Regulators (Rev. B)
    PDF, 187 Kb, Revision: B, Datei veröffentlicht: Apr 23, 2013
    This application report describes two LM2576-based designs that provide up to 3A of current for batterycharging.
  • Battery Charging
    PDF, 146 Kb, Datei veröffentlicht: Mar 21, 2007
  • AN-776 20-W SIMPLE SWITCHER Forward Converter (Rev. A)
    PDF, 593 Kb, Revision: A, Datei veröffentlicht: Apr 23, 2013
    This application note provides information about the 20-watt simple switcher forward converter.
  • AN-1246 Stresses in Wide Input DC-DC Converters (Rev. C)
    PDF, 427 Kb, Revision: C, Datei veröffentlicht: Apr 23, 2013
    This application note discusses stresses in wide input DC-DC converters.
  • Buck Converters Provide a Battery Charger and System Power
    PDF, 61 Kb, Datei veröffentlicht: Mar 21, 2007
  • AN-1197 Selecting Inductors for Buck Converters (Rev. B)
    PDF, 558 Kb, Revision: B, Datei veröffentlicht: Apr 23, 2013
    This application report provides design information to help select an off-the-shelf inductor for anycontinuous-mode buck converter application.
  • AN-2162 Simple Success With Conducted EMI From DC-DC Converters (Rev. C)
    PDF, 2.5 Mb, Revision: C, Datei veröffentlicht: Apr 24, 2013
    Electromagnetic Interference (EMI) is an unwanted effect between two electrical systems as a result ofeither electromagnetic radiation or electromagnetic conduction. EMI is the major adverse effect caused bythe application of switch-mode power supplies (SMPS). In switching power supplies EMI noise isunavoidable due to the switching actions of the semiconductor devices and resulting disconti
  • Semiconductor and IC Package Thermal Metrics (Rev. C)
    PDF, 201 Kb, Revision: C, Datei veröffentlicht: Apr 19, 2016
  • Switching Regulator Fundamentals (Rev. A)
    PDF, 324 Kb, Revision: A, Datei veröffentlicht: Sep 23, 2016
    Theswitchingregulatoris increasingin popularitybecauseit offersthe advantagesof higherpowerconversionefficiencyand increaseddesignflexibility(multipleoutputvoltagesof differentpolaritiescan begeneratedfroma singleinputvoltage).
  • Input and Output Capacitor Selection
    PDF, 219 Kb, Datei veröffentlicht: Sep 19, 2005
  • AN-643 EMI/RFI Board Design (Rev. B)
    PDF, 742 Kb, Revision: B, Datei veröffentlicht: May 3, 2004
    Application Note 643 EMI/RFI Board Design
  • AN-1149 Layout Guidelines for Switching Power Supplies (Rev. C)
    PDF, 82 Kb, Revision: C, Datei veröffentlicht: Apr 23, 2013
    When designing a high frequency switching regulated power supply layout is very important. Using agood layout can solve many problems associated with these types of supplies. The problems due to a badlayout are often seen at high current levels and are usually more obvious at large input to output voltagedifferentials. Some of the main problems are loss of regulation at high output current
  • AN-1229 SIMPLE SWITCHER PCB Layout Guidelines (Rev. C)
    PDF, 374 Kb, Revision: C, Datei veröffentlicht: Apr 23, 2013
    This application report provides SIMPLE SWITCHER™ PCB layout guidelines.
  • AN-1520 A Guide to Board Layout for Best Thermal Resistance for Exposed Packages (Rev. B)
    PDF, 9.2 Mb, Revision: B, Datei veröffentlicht: Apr 23, 2013
    This thermal application report provides guidelines for the optimal board layout to achieve the best thermalresistance for exposed packages. The thermal resistance between junction-to-ambient (ОёJA) is highlydependent on the PCB (Printed Circuit Board) design factors. This becomes more critical for packageshaving very low thermal resistance between junction-to-case such as exposed pad TSSOP
  • AN-1889 How to Measure the Loop Transfer Function of Power Supplies (Rev. A)
    PDF, 2.7 Mb, Revision: A, Datei veröffentlicht: Apr 23, 2013
    This application report shows how to measure the critical points of a bode plot with only an audiogenerator (or simple signal generator) and an oscilloscope. The method is explained in an easy to followstep-by-step manner so that a power supply designer can start performing these measurements in a shortamount of time.
  • AN-1566 Techniques for Thermal Analysis of Switching Power Supply Designs (Rev. A)
    PDF, 1.4 Mb, Revision: A, Datei veröffentlicht: Apr 23, 2013
    This application note provides thermal power analysis techniques for analyzing the power IC.
  • AN-2155 Layout Tips for EMI Reduction in DC/ DC Converters (Rev. A)
    PDF, 3.6 Mb, Revision: A, Datei veröffentlicht: Apr 23, 2013
    This application note will explore how the layout of your DC/DC power supply can significantly affect theamount of EMI that it produces. It will discuss several variations of a layout analyze the results andprovide answers to some common EMI questions such whether or not to use a shielded inductor.
  • Low EMI Layout Made SIMPLE With LM43600/1/2/3 and LM46000/1/2 (Rev. A)
    PDF, 512 Kb, Revision: A, Datei veröffentlicht: Sep 12, 2014
    Printed Circuit Board (PCB) layout for Switched Mode Power Supplies (SMPS) is critical to achieve proper converter operation good thermal performance and excellent radiated EMI performance. Optimized board layout for low radiated EMI is made very simple by the package and pin arrangement of the SIMPLE SWITCHER Synchronous Buck Converter family LM4360x and LM4600x

Modellreihe

Herstellerklassifikation

  • Semiconductors > Power Management > DC/DC Switching Regulator > Step-Down (Buck) > Buck Converter (Integrated Switch)

Andere Namen:

LM2576TADJ, LM2576T ADJ

Verwandte Veröffentlichungen