Datasheet Texas Instruments OPA301AIDBVR — Datenblatt

HerstellerTexas Instruments
SerieOPA301
ArtikelnummerOPA301AIDBVR
Datasheet Texas Instruments OPA301AIDBVR

Rauscharmer, schneller 16-Bit-CMOS-Operationsverstärker mit hoher Geschwindigkeit 5-SOT-23 -40 bis 125

Datenblätter

Low-Noise, High-Speed,16-Bit Accurate, CMOS Operational Amplifier datasheet
PDF, 1.2 Mb, Revision: D, Datei veröffentlicht: Jun 13, 2007
Auszug aus dem Dokument

Preise

Status

Lifecycle StatusActive (Recommended for new designs)
Manufacture's Sample AvailabilityNo

Verpackung

Pin5
Package TypeDBV
Industry STD TermSOT-23
JEDEC CodeR-PDSO-G
Package QTY3000
CarrierLARGE T&R
Device MarkingAUP
Width (mm)1.6
Length (mm)2.9
Thickness (mm)1.2
Pitch (mm).95
Max Height (mm)1.45
Mechanical DataHerunterladen

Parameter

2nd Harmonic75 dBc
3rd Harmonic79 dBc
@ MHz1
Acl, min spec gain1 V/V
Additional FeaturesShutdown
ArchitectureCMOS,Voltage FB
BW @ Acl150 MHz
CMRR(Min)66 dB
CMRR(Typ)80 dB
GBW(Typ)150 MHz
Input Bias Current(Max)5 pA
Iq per channel(Max)12 mA
Iq per channel(Typ)9.5 mA
Number of Channels1
Offset Drift(Typ)2.5 uV/C
Operating Temperature Range-40 to 125 C
Output Current(Typ)70 mA
Package GroupSOT-23
Package Size: mm2:W x L5SOT-23: 8 mm2: 2.8 x 2.9(SOT-23) PKG
Rail-to-RailIn to V-,Out
RatingCatalog
Slew Rate(Typ)80 V/us
Total Supply Voltage(Max)5.5 +5V=5, +/-5V=10
Total Supply Voltage(Min)2.7 +5V=5, +/-5V=10
Vn at 1kHz(Typ)3 nV/rtHz
Vn at Flatband(Typ)3 nV/rtHz
Vos (Offset Voltage @ 25C)(Max)5 mV

Öko-Plan

RoHSCompliant

Anwendungshinweise

  • High-Voltage Signal Conditioning for Low Voltage ADCs
    PDF, 135 Kb, Datei veröffentlicht: Jun 15, 2004
    Analog designers are frequently required to develop circuits that convert high-voltage signals to levels acceptable for low-voltage data converters. This paper describes several solutions for this common task using modern amplifiers and typical power supplies. Five examples of conditioning ±10V bipolar signals for low-voltage single-rail analog-to-digital converters(ADCs) are presented:
  • High-Voltage Signal Conditioning for Differential ADCs
    PDF, 125 Kb, Datei veröffentlicht: Jun 14, 2004
    Analog designers are frequently required to convert high-voltage signals to levels acceptable to low-voltage data converters with differential inputs. This paper describes solutions for this common task using modern amplifiers and typical power supplies. Three examples of conditioning В±10V bipolar signals for low-voltage analog-to-digital converters (ADCs) are shown: a single-supply design,
  • Tuning in Amplifiers
    PDF, 44 Kb, Datei veröffentlicht: Oct 2, 2000
    Have you ever had the experience of designing an analog gain block with an amplifier that is specified to be unity gain stable only to find that it is oscillating out of control in your circuit? Or have you ever replaced a stable voltage feedback amplifier with a current feedback amplifier to find that the current feedback amplifier immediately oscillates when placed in the amplifier socket? Oscil
  • Single-Supply Operation of Operational Amplifiers
    PDF, 77 Kb, Datei veröffentlicht: Oct 2, 2000
    Operation of op amps from single supply voltages is useful when negative supply voltages are not available. Furthermore, certain applications using high voltage and high current op amps can derive important benefits from single supply operation.
  • Op Amp Performance Analysis
    PDF, 76 Kb, Datei veröffentlicht: Oct 2, 2000
    This bulletin reflects the analysis power gained through knowledge of an op amp circuit's feedback factor. Feedback dictates the performance of an op amp both in function and in quality. The major specifications of the amplifier descibe an open-loop device awaiting feedback direction of the end circuit's function. Just how well the amplifier performs the function reflects through the feedback inte

Modellreihe

Herstellerklassifikation

  • Semiconductors > Amplifiers > Operational Amplifiers (Op Amps) > High-Speed Op Amps (>=50MHz)