Datasheet Texas Instruments THS6042CDDAG3 — Datenblatt

HerstellerTexas Instruments
SerieTHS6042
ArtikelnummerTHS6042CDDAG3
Datasheet Texas Instruments THS6042CDDAG3

350 mA, +/- 12 V ADSL CPE-Leitungstreiber 8-SO PowerPAD 0 bis 70

Datenblätter

350 mA +/-12V ADSL CPE Line Drivers datasheet
PDF, 1.6 Mb, Revision: G, Datei veröffentlicht: Dec 11, 2001
Auszug aus dem Dokument

Preise

Status

Lifecycle StatusActive (Recommended for new designs)
Manufacture's Sample AvailabilityNo

Verpackung

Pin8
Package TypeDDA
Industry STD TermHSOIC
JEDEC CodeR-PDSO-G
Package QTY75
CarrierTUBE
Device Marking6042C
Width (mm)3.9
Length (mm)4.89
Thickness (mm)1.48
Pitch (mm)1.27
Max Height (mm)1.7
Mechanical DataHerunterladen

Parameter

2nd Harmonic67 dBc
3rd Harmonic96 dBc
@ MHz1
Acl, min spec gain1 V/V
Additional FeaturesN/A
ArchitectureCurrent FB
BW @ Acl120 MHz
CMRR(Min)59 dB
CMRR(Typ)68 dB
GBW(Typ)120 MHz
Input Bias Current(Max)10000000 pA
Iq per channel(Max)10.5 mA
Iq per channel(Typ)8.2 mA
Number of Channels2
Offset Drift(Typ)20 uV/C
Operating Temperature Range-40 to 85,0 to 70 C
Output Current(Typ)350 mA
Package GroupSO PowerPAD
Package Size: mm2:W x L8SO PowerPAD: 29 mm2: 6 x 4.9(SO PowerPAD) PKG
Rail-to-RailNo
RatingCatalog
Slew Rate(Typ)1400 V/us
Total Supply Voltage(Max)33 +5V=5, +/-5V=10
Total Supply Voltage(Min)9 +5V=5, +/-5V=10
Vn at 1kHz(Typ)2.4 nV/rtHz
Vn at Flatband(Typ)2.2 nV/rtHz
Vos (Offset Voltage @ 25C)(Max)16 mV

Öko-Plan

RoHSCompliant

Design Kits und Evaluierungsmodule

  • Evaluation Modules & Boards: THS6042EVM
    THS6042 Evaluation Module
    Lifecycle Status: Active (Recommended for new designs)

Anwendungshinweise

  • Active Output Impedance for ADSL Line Drivers
    PDF, 636 Kb, Datei veröffentlicht: Nov 26, 2002
    Signal termination is very common in bidirectional communication systems. Termination allows for receiving signals while transmitting different signals at the same time. With the increasing popularity of asymmetrical digital subscriber lines (ADSL), the requirement for a low power line driver amplifier combined with line termination becomes a very difficult goal. This application note examines the
  • Noise Analysis for High Speed Op Amps (Rev. A)
    PDF, 256 Kb, Revision: A, Datei veröffentlicht: Jan 17, 2005
    As system bandwidths have increased an accurate estimate of the noise contribution for each element in the signal channel has become increasingly important. Many designers are not however particularly comfortable with the calculations required to predict the total noise for an op amp or in the conversions between the different descriptions of noise. Considerable inconsistency between manufactu

Modellreihe

Herstellerklassifikation

  • Semiconductors > Amplifiers > Operational Amplifiers (Op Amps) > High-Speed Op Amps (>=50MHz)